|
|
Thread Tools |
08-25-2020, 10:23 PM | #1711 |
Cobra Viper
Join Date: Sep 2018
Location: Deadwood
Posts: 280
|
New pics
Cowpoke Last edited by Jericho Wilson; 08-29-2020 at 07:56 PM.. |
08-25-2020, 11:59 PM | #1712 |
Hog Driver
Join Date: Aug 2008
Location: Georgia
Posts: 12,235
|
|
09-08-2020, 03:21 PM | #1713 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,266
|
I printed a test piece of the rear end of the Nightlinger chuck wagon so I could dial in a bunch of features without wasting an entire print on it:
I am still working on the trailer hitching connection... The wagon cover ribs are still removable: The rear door converts to a counter/table surface with the use of a hinge and a removable table leg: Slide the table leg out of the bracket... Insert the short end of the table leg back into the bracket... Then open the door and let it rest as a table... The drawers are removable: And I also worked out an acceptable means of hanging the slop bucket under the rear platform. Here is my much-smaller test piece of the region resting in place above where it would really go when part of the larger print: The connection method I used is much stronger than a simple hook but still somewhat fakes the appearance of being just a hook unless you flip if over and look at the bottom: And the water barrel on the side of this wagon will feature a removable lid. Here is a small sliver of barrel top with a test lid: I have a few little issues to clean up but Mr. Nightlinger's chuck wagon is dangerously close to being ready for a final print!
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
09-08-2020, 08:47 PM | #1714 |
Hog Driver
Join Date: Aug 2008
Location: Georgia
Posts: 12,235
|
Looking good, Zap!
|
09-08-2020, 11:52 PM | #1715 |
LNC Commander
Join Date: Oct 2009
Location: Sbartek's Guest Room
Posts: 24,568
|
Cowpoke!
__________________
|
09-09-2020, 12:21 AM | #1716 |
Bald Master
Join Date: Apr 2011
Location: Wolverine Lake, MI
Posts: 15,122
|
Cowpoke(s)!
__________________
"Once got busy in the back of a Buzz Boar!" FEEDBACK: http://www.hisstank.com/forum/buy-se...ck-thread.html CUSTOM WORK: https://www.hisstank.com/forum/g-i-j...s-customs.html |
09-09-2020, 04:41 AM | #1717 |
LNC Commander
Join Date: Oct 2009
Location: Sbartek's Guest Room
Posts: 24,568
|
Cowpoking!
__________________
|
09-10-2020, 07:58 AM | #1718 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,266
|
I need a Nightlinger recipe. I have the bearded/bald head from the "most wanted" head pack that might be close enough but I need help with the buck and accessories. Anyone?
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
09-13-2020, 02:01 AM | #1719 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,266
|
Quote:
And speaking of which, I still need to come up with a tow rope to connect the trailer to the wagon plus re-print the door/table piece (broke the hinge off during installation) and print a couple more ribs, but the Nightlinger chuck wagon has more or less landed at last:
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
09-13-2020, 07:55 AM | #1720 |
Bald Master
Join Date: Apr 2011
Location: Wolverine Lake, MI
Posts: 15,122
|
Been silently watching your progress, Zap...amazing (near) end result!
__________________
"Once got busy in the back of a Buzz Boar!" FEEDBACK: http://www.hisstank.com/forum/buy-se...ck-thread.html CUSTOM WORK: https://www.hisstank.com/forum/g-i-j...s-customs.html |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lost Planet 1/18th scale figure line | r3v3n63 | G.I. Joe News and Rumors | 44 | 01-19-2016 05:01 PM |
Revoltech "RevolMini" 1/18th scale figure line | r3v3n63 | Toys | 48 | 06-10-2015 07:19 PM |
1:18th Scale Planes & lots of Misc toys, ML, etc... for sale | Scotty97 | G.I. Joe on Ebay | 2 | 11-05-2009 02:47 AM |
RoC Toys:Check your local five-and-dime type stores.. | Steel | G.I. Joe Live Action Movie | 0 | 07-02-2009 09:21 AM |
|
|
Recent Off Topic Threads |
What song are you listening to? |
Hisstank Late Night thread... |
Star Wars 3 3/4 discussion thread |
JazWares 18th Halo |
4" Fortnite from Jazwares |