|
Community Links |
Social Groups |
Pictures & Albums |
Members List |
Search Forums |
Advanced Search |
Go to Page... |
|
Thread Tools |
05-25-2019, 10:57 AM | #291 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
At long last, the Mauler gas grenade launcher has been acquired and modeled. Here is a pair (left/right):
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-28-2019, 11:15 AM | #292 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
I finally took a moment to make a rifle sling to use on these test printed sling hooks and slides:
They are quite fragile, but they are also functional. I might beef them up a bit and try the next-strongest material or two to see if I can get a sturdy offering available.
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-28-2019, 11:20 AM | #293 |
Hisstank.Com General
Join Date: Jul 2011
Location: tampa fl
Posts: 5,106
|
Hey Zap. What’s the best method in separating MTF hip/crotch? I want to use your BF/MTF conversion kit but need some help to do it right.
|
05-28-2019, 11:22 AM | #294 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
Quote:
The short answer is: I use a bench vise with the waist section wrapped in a shop towel to prevent marring.
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-29-2019, 07:10 PM | #295 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
So, um...some of my prints have arrived...
I'll be sharing the de-sprued results over the next day or so.
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-29-2019, 07:45 PM | #296 |
I just want foam gliders.
Join Date: Sep 2007
Location: Tooele (two-willa), Utah
Posts: 18,727
|
Awesome, can't wait!
__________________
Problems with the Club? Click me.... How to post pics to Hisstank? Click me.... BST Feedback |
05-29-2019, 08:03 PM | #297 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
First up, some vintage Skystriker reproduction parts...
Front landing gear cover: Rear landing gear cover: Landing gear retention clips: Small missile: And here they are in use: ....And in the next post...the Skystriker IRST pod in modern and vintage versions!
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-29-2019, 08:29 PM | #298 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
IRST pods in vintage and modern era models:
Vintage: Modern:
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-29-2019, 09:08 PM | #299 |
A Makeupless Clown
Join Date: Sep 2015
Location: Ohio
Posts: 5,271
|
OK, last up for this evening we have some Terror Drome parts. Here are the gun tips, large and small:
I made a mistake with the overall height on one of them, so that needs to be addressed. And I also made an attempt at designing a repair piece to help Xerofall put his door lever arm thingamajig back in place. I tried to keep it absolutely minimal in terms of space so that it will blend in as much as possible: The idea here, by his request, was to make a glue-on set of hinges to put up on the wall near where the original hinges had broken off. The basic design is ok but as you can see, the shafts are oblong in one axis rather than round. I thought my design would have enough flexibility to tolerate the difference in dimensions but in practice it's a bridge too far. The "fat" direction pressing against the jaws of the hinges causes warping of the clip's back board so a revision will be needed. Coming up tomorrow: Mauler parts STUN parts Night Raven parts ASP blast shield Snowcat parts Moray machine gun VAMP steering wheel maybe more...
__________________
Torso Adapters and Alternate Neck Pegs for MTF and BFS Figures Reproduction Vehicle Parts 3d-Printed Parts Gallery My BST Thread | My Feedback Thread | My Shapeways 3d Print Shop (1/18 scale creations) |
05-30-2019, 09:55 AM | #300 |
I just want foam gliders.
Join Date: Sep 2007
Location: Tooele (two-willa), Utah
Posts: 18,727
|
Sweet! Don't put too much R&D into those Terror Drome clips for me... I just want something simple to hold those legs. But if they work I think a lot of people would want them.
__________________
Problems with the Club? Click me.... How to post pics to Hisstank? Click me.... BST Feedback |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dioramas Joe Scale Diorama Detail Set | Capt OG ReadMo | G.I. Joe Customs Finished Projects | 11 | 01-20-2019 02:11 PM |
Dioramas 3 3/4"/4" Scale Gear and Diorama Objects from Prize Inside! | TrentTroop | G.I. Joe Customs Finished Projects | 17 | 07-17-2017 12:13 PM |
Gi joe cobra custom display parts lot diorama | NIKOLAI | G.I. Joe on Ebay | 0 | 07-04-2017 11:17 AM |
1/18 scale diorama and custom parts | Hoyrat | G.I. Joe Buy Sell Trade | 1 | 02-14-2014 01:59 AM |
Hot Toys 1/6 Scale Terminator Diorama | TOYARK.COM | Toys | 0 | 02-03-2009 08:40 AM |
|
|